---
title: "M22×2.5 tap drill 19.5 mm, clearance 23 mm"
description: "M22×2.5: tap drill 19.5 mm, clearance hole 23 mm, 34 mm hex. Full thread dimensions, how to identify it, and torque."
url: https://atoneplace.net/fastener/m22-2-5/
site: "At One Place"
---

# M22×2.5 thread

**M22×2.5 tap drill: 19.5 mm**

Clearance hole 23 mm · 34 mm hex

M22×2.5 is a coarse metric thread with a 22 mm (0.866") major diameter and 2.5 mm pitch. Tap it with a 19.5 mm drill; drill 23 mm to pass a bolt through.

## The numbers

- **Designation:** M22×2.5
- **Major diameter:** 22 mm / 0.866"
- **Minor diameter:** 19.294 mm
- **Pitch:** 2.5 mm pitch
- **Tap drill (75% thread):** 19.5 mm — 19.5 mm
- **Clearance hole (close fit):** 23 mm / 0.906"
- **Hex across flats:** 34 mm

## How to measure what you have

1. Measure across the thread crests with calipers. A used M22×2.5 reads a little under 22 mm — the crests are truncated by the standard, then worn and plated, so anything from about 21.6 mm up is consistent with this size.
2. Measure the pitch: put a rule against the threads and count the distance over ten crests, then divide by ten. This one should give 2.5 mm.
3. A thread pitch gauge settles it in seconds and costs very little. Guessing between a coarse and a fine thread of the same diameter is the usual way a thread gets stripped.

## Tightening torque

**Typical torque: 490–660 N·m**

361.5–486.9 lb·ft

> Plain steel property class 8.8 or SAE grade 5, dry threads, tightened to about 65% of yield. Lubricated threads reach the same preload at 20-30% less torque. Where the manufacturer publishes a figure — spark plugs, wheel nuts, cylinder heads — use theirs.

## Where this size turns up

- Bridge and crane structural connections
- Large flange bolting
- Heavy plant pivot pins

> ISO 4014:2011 gives 34 mm across flats. Older ISO and DIN 931 parts take a 32 mm spanner, so both exist in service.

## Other threads at this diameter

*Same diameter, different pitch. Forcing the wrong one strips the thread in a turn or two.*

| Thread | Pitch | Tap drill | Clearance |
| --- | --- | --- | --- |
| M22×1.5 | 1.5 mm | 20.5 mm | 23 mm |

## Common questions

### What size drill for an M22×2.5 tap?

19.5 mm (19.5 mm), which gives about 75% thread engagement.

### What clearance hole for M22×2.5?

23 mm for a close fit — enough to pass the bolt without slop.

### What spanner fits M22×2.5?

34 mm across the flats on a standard hex head.

## Related pages

- [M22×1.5](https://atoneplace.net/fastener/m22-1-5/)
- [M20×2.5](https://atoneplace.net/fastener/m20-2-5/)
- [M24×3](https://atoneplace.net/fastener/m24-3/)
- [M20×1.5](https://atoneplace.net/fastener/m20-1-5/)
- [M20×2](https://atoneplace.net/fastener/m20-2/)
- [M24×2](https://atoneplace.net/fastener/m24-2/)
- [M24×1.5](https://atoneplace.net/fastener/m24-1-5/)
- [M18×2.5](https://atoneplace.net/fastener/m18-2-5/)
- [M18×1.5](https://atoneplace.net/fastener/m18-1-5/)
- [M27×3](https://atoneplace.net/fastener/m27-3/)
- [M27×2](https://atoneplace.net/fastener/m27-2/)

## Sources

- Official vendor product documentation — At One Place (/about/)
- Typical range compiled from manufacturer specifications — At One Place (/about/)