---
title: "9/16\"-18 UNF tap drill 33/64\", clearance 15.08 mm"
description: "9/16\"-18 UNF: tap drill 33/64\", clearance hole 15.08 mm, 20.64 mm hex. Full thread dimensions, how to identify it, and torque."
url: https://atoneplace.net/fastener/nine-sixteenths-18/
site: "At One Place"
---

# 9/16"-18 UNF thread

**9/16"-18 UNF tap drill: 33/64"**

Clearance hole 15.08 mm · 20.64 mm hex

9/16"-18 UNF is a fine Unified inch thread with a 14.287 mm (0.562") major diameter and 18 threads per inch (1.411 mm pitch). Tap it with a 33/64" drill; drill 15.08 mm to pass a bolt through.

## The numbers

- **Designation:** 9/16"-18 UNF
- **Major diameter:** 14.287 mm / 0.562"
- **Minor diameter:** 12.76 mm
- **Pitch:** 18 threads per inch (1.411 mm pitch)
- **Tap drill (75% thread):** 33/64" — 13.1 mm
- **Clearance hole (close fit):** 15.08 mm / 0.594"
- **Hex across flats:** 20.64 mm

## How to measure what you have

1. Measure across the thread crests with calipers. A used 9/16"-18 UNF reads a little under 14.287 mm — the crests are truncated by the standard, then worn and plated, so anything from about 13.9 mm up is consistent with this size.
2. Count the threads crossing one inch. This one gives 18.
3. A thread pitch gauge settles it in seconds and costs very little. Guessing between a coarse and a fine thread of the same diameter is the usual way a thread gets stripped.

## Tightening torque

**Typical torque: 132–180 N·m**

97.4–132.8 lb·ft

> Plain steel property class 8.8 or SAE grade 5, dry threads, tightened to about 65% of yield. Lubricated threads reach the same preload at 20-30% less torque. Where the manufacturer publishes a figure — spark plugs, wheel nuts, cylinder heads — use theirs.

## Where this size turns up

- Automotive fine-thread chassis bolts
- Machinery adjusting studs

> Not the bicycle pedal thread, which is 9/16"-20 and will cross-thread in a 9/16"-18 crank.

## Other threads at this diameter

*Same diameter, different pitch. Forcing the wrong one strips the thread in a turn or two.*

| Thread | Pitch | Tap drill | Clearance |
| --- | --- | --- | --- |
| 9/16"-12 UNC | 12 tpi | 31/64" | 15.08 mm |

## Common questions

### What size drill for an 9/16"-18 UNF tap?

33/64" (13.1 mm), which gives about 75% thread engagement.

### What clearance hole for 9/16"-18 UNF?

15.08 mm for a close fit — enough to pass the bolt without slop.

### What spanner fits 9/16"-18 UNF?

20.64 mm across the flats on a standard hex head.

## Related pages

- [9/16"-12 UNC](https://atoneplace.net/fastener/nine-sixteenths-12/)
- [1/2"-13 UNC](https://atoneplace.net/fastener/half-13/)
- [1/2"-20 UNF](https://atoneplace.net/fastener/half-20/)
- [1/2"-28 UNEF](https://atoneplace.net/fastener/half-28/)
- [5/8"-11 UNC](https://atoneplace.net/fastener/five-eighths-11/)
- [5/8"-18 UNF](https://atoneplace.net/fastener/five-eighths-18/)
- [5/8"-27 UNS](https://atoneplace.net/fastener/five-eighths-27/)
- [7/16"-14 UNC](https://atoneplace.net/fastener/seven-sixteenths-14/)
- [7/16"-20 UNF](https://atoneplace.net/fastener/seven-sixteenths-20/)
- [3/8"-16 UNC](https://atoneplace.net/fastener/three-eighths-16/)
- [3/8"-24 UNF](https://atoneplace.net/fastener/three-eighths-24/)

## Sources

- Official vendor product documentation — At One Place (/about/)
- Typical range compiled from manufacturer specifications — At One Place (/about/)