---
title: "#1-72 UNF tap drill #53, clearance 2.06 mm"
description: "#1-72 UNF: tap drill #53, clearance hole 2.06 mm. Full thread dimensions, how to identify it, and torque."
url: https://atoneplace.net/fastener/number-1-72/
site: "At One Place"
---

# #1-72 UNF thread

**#1-72 UNF tap drill: #53**

Clearance hole 2.06 mm

#1-72 UNF is a fine Unified inch thread with a 1.854 mm (0.073") major diameter and 72 threads per inch (0.353 mm pitch). Tap it with a #53 drill; drill 2.06 mm to pass a bolt through.

## The numbers

- **Designation:** #1-72 UNF
- **Major diameter:** 1.854 mm / 0.073"
- **Minor diameter:** 1.472 mm
- **Pitch:** 72 threads per inch (0.353 mm pitch)
- **Tap drill (75% thread):** #53 — 1.51 mm
- **Clearance hole (close fit):** 2.06 mm / 0.081"

## How to measure what you have

1. Measure across the thread crests with calipers. A used #1-72 UNF reads a little under 1.854 mm — the crests are truncated by the standard, then worn and plated, so anything from about 1.5 mm up is consistent with this size.
2. Count the threads crossing one inch. This one gives 72.
3. A thread pitch gauge settles it in seconds and costs very little. Guessing between a coarse and a fine thread of the same diameter is the usual way a thread gets stripped.

## Tightening torque

No torque figure is given for this size. Small and fine threads like this are generally not supplied to a strength grade, and in most assemblies the tapped material strips before the fastener yields — so a published bolt torque would be the wrong limit to work to. Tighten to snug plus a small turn, or use the figure the manufacturer of the part specifies.

## Where this size turns up

- Miniature instrument and connector hardware
- Model engineering

## Other threads at this diameter

*Same diameter, different pitch. Forcing the wrong one strips the thread in a turn or two.*

| Thread | Pitch | Tap drill | Clearance |
| --- | --- | --- | --- |
| #1-64 UNC | 64 tpi | #53 | 2.06 mm |

## Common questions

### What size drill for an #1-72 UNF tap?

#53 (1.51 mm), which gives about 75% thread engagement.

### What clearance hole for #1-72 UNF?

2.06 mm for a close fit — enough to pass the bolt without slop.

## Related pages

- [#1-64 UNC](https://atoneplace.net/fastener/number-1-64/)
- [#2-56 UNC](https://atoneplace.net/fastener/number-2-56/)
- [#0-80 UNF](https://atoneplace.net/fastener/number-0-80/)
- [#2-64 UNF](https://atoneplace.net/fastener/number-2-64/)
- [#3-48 UNC](https://atoneplace.net/fastener/number-3-48/)
- [#4-40 UNC](https://atoneplace.net/fastener/number-4-40/)
- [#4-48 UNF](https://atoneplace.net/fastener/number-4-48/)
- [#5-40 UNC](https://atoneplace.net/fastener/number-5-40/)
- [#6-32 UNC](https://atoneplace.net/fastener/number-6-32/)
- [#6-40 UNF](https://atoneplace.net/fastener/number-6-40/)
- [#8-32 UNC](https://atoneplace.net/fastener/number-8-32/)

## Sources

- Official vendor product documentation — At One Place (/about/)