---
title: "#2-64 UNF tap drill #50, clearance 2.44 mm"
description: "#2-64 UNF: tap drill #50, clearance hole 2.44 mm. Full thread dimensions, how to identify it, and torque."
url: https://atoneplace.net/fastener/number-2-64/
site: "At One Place"
---

# #2-64 UNF thread

**#2-64 UNF tap drill: #50**

Clearance hole 2.44 mm

#2-64 UNF is a fine Unified inch thread with a 2.184 mm (0.086") major diameter and 64 threads per inch (0.397 mm pitch). Tap it with a #50 drill; drill 2.44 mm to pass a bolt through.

## The numbers

- **Designation:** #2-64 UNF
- **Major diameter:** 2.184 mm / 0.086"
- **Minor diameter:** 1.755 mm
- **Pitch:** 64 threads per inch (0.397 mm pitch)
- **Tap drill (75% thread):** #50 — 1.78 mm
- **Clearance hole (close fit):** 2.44 mm / 0.096"

## How to measure what you have

1. Measure across the thread crests with calipers. A used #2-64 UNF reads a little under 2.184 mm — the crests are truncated by the standard, then worn and plated, so anything from about 1.8 mm up is consistent with this size.
2. Count the threads crossing one inch. This one gives 64.
3. A thread pitch gauge settles it in seconds and costs very little. Guessing between a coarse and a fine thread of the same diameter is the usual way a thread gets stripped.

## Tightening torque

No torque figure is given for this size. Small and fine threads like this are generally not supplied to a strength grade, and in most assemblies the tapped material strips before the fastener yields — so a published bolt torque would be the wrong limit to work to. Tighten to snug plus a small turn, or use the figure the manufacturer of the part specifies.

## Where this size turns up

- Small connector and instrument screws
- Firearm sight and accessory screws

## Other threads at this diameter

*Same diameter, different pitch. Forcing the wrong one strips the thread in a turn or two.*

| Thread | Pitch | Tap drill | Clearance |
| --- | --- | --- | --- |
| #2-56 UNC | 56 tpi | #50 | 2.44 mm |

## Common questions

### What size drill for an #2-64 UNF tap?

#50 (1.78 mm), which gives about 75% thread engagement.

### What clearance hole for #2-64 UNF?

2.44 mm for a close fit — enough to pass the bolt without slop.

## Related pages

- [#2-56 UNC](https://atoneplace.net/fastener/number-2-56/)
- [#1-64 UNC](https://atoneplace.net/fastener/number-1-64/)
- [#1-72 UNF](https://atoneplace.net/fastener/number-1-72/)
- [#3-48 UNC](https://atoneplace.net/fastener/number-3-48/)
- [#0-80 UNF](https://atoneplace.net/fastener/number-0-80/)
- [#4-40 UNC](https://atoneplace.net/fastener/number-4-40/)
- [#4-48 UNF](https://atoneplace.net/fastener/number-4-48/)
- [#5-40 UNC](https://atoneplace.net/fastener/number-5-40/)
- [#6-32 UNC](https://atoneplace.net/fastener/number-6-32/)
- [#6-40 UNF](https://atoneplace.net/fastener/number-6-40/)
- [#8-32 UNC](https://atoneplace.net/fastener/number-8-32/)

## Sources

- Official vendor product documentation — At One Place (/about/)