---
title: "Which blade cuts plastic pipe?"
description: "A fine 24 TPI hacksaw or a proper pipe cutter — and deburr the inside afterwards, which is the step people skip. The ranked options, the technique that changes the o"
url: https://atoneplace.net/which/blade-plastic-pipe/
site: "At One Place"
---

# Which blade cuts plastic pipe?

**Which blade cuts plastic pipe?: A fine 24 TPI hacksaw or a proper pipe cutter — and deburr the inside afterwards, which is the step people skip.**

A cut on a plastic pipe has to be square and clean because the joint depends on it: a solvent-weld socket needs the pipe to seat fully to its stop, and an out-of-square cut leaves the joint bearing on one side. Burrs matter more than they look. An external burr scrapes the sealing ring in a push-fit joint or drags cement out of a solvent joint, and an internal burr disturbs the flow and, in waste pipes, gives debris something to catch on. Cold weather changes the calculation with ratchet shears: PVC becomes noticeably more brittle below about 5 °C, and the shear can split the pipe rather than cut it, so a saw is the safer choice.

## The options, ranked

*Ranked best-first for the stated job. The third column is why the others exist.*

| Option | Good at | Bad at |
| --- | --- | --- |
| Rotary pipe cutter | Square, clean cuts every time with no swarf, and it works in tight spaces. | Leaves a raised internal burr that must be reamed out. |
| Ratchet shear cutter | Instant one-handed cuts in small-diameter PVC, PEX and polyethylene. | Deforms the pipe end oval on larger sizes, and can crack PVC in cold weather. |
| 24 TPI hacksaw | Cuts anything and is always to hand. | Hard to keep square by hand; a mitre box or a wrap of paper as a guide helps. |
| Reciprocating saw with a fine blade | Fast in awkward positions such as under a floor. | Wanders badly, melts the plastic and leaves a poor edge for a solvent joint. |

## Technique that changes the outcome

1. Mark all the way round and cut square, using a mitre box or a taped guide
2. Deburr and chamfer the outside edge, and ream the inside
3. Wipe the cut end clean before priming or pushing into a fitting
4. Warm PVC pipe before shearing it in cold conditions, or use a saw instead

## What goes wrong

- Leaving a burr inside a waste pipe
- Ratchet shears on cold PVC
- Cutting so short that the pipe cannot reach the stop in the fitting

> Compiled practical guidance rather than a published standard. Product formulations vary by brand and market, so read the label — and where the work is structural, electrical or gas, the regulations that apply where you are govern rather than anything here.

## Other blade questions

| For | Use |
| --- | --- |
| Metal | A bi-metal or carbide-tooth blade with at least three teeth in the cut — that tooth-count rule matters more than the machine. |
| Tile | A continuous-rim diamond blade with water — and cut wet, because dry cutting tile produces respirable silica dust. |
| Wood | 24 teeth for ripping and framing, 40 for general work, 60-80 for a clean crosscut finish. |
| Plywood without tearout | A sharp 60-80 tooth blade, a scoring pass, tape on the line, and the good face oriented for the tool you are using. |
| Brick | A segmented-rim diamond blade, cut wet or with on-tool extraction — brick and mortar dust is a serious silica hazard. |
| Laminate | A triple-chip or negative-hook blade for worktops, and a reverse-tooth jigsaw blade for laminate flooring cut face up. |
| Acrylic | A triple-chip negative-hook blade on a table saw, or score-and-snap for thin sheet — and keep the feed steady so it does not melt. |
| Glass | None — a tungsten carbide scoring wheel, one firm pass with oil, then snap it. And toughened glass cannot be cut at all. |
| Plasterboard | A utility knife for straight cuts and a jab saw or multi-tool for cutouts — a circular saw is the wrong tool entirely. |

## Common questions

### Which blade cuts plastic pipe?

A fine 24 TPI hacksaw or a proper pipe cutter — and deburr the inside afterwards, which is the step people skip.

### What should I avoid?

Leaving a burr inside a waste pipe Ratchet shears on cold PVC Cutting so short that the pipe cannot reach the stop in the fitting

## Related pages

- [Which blade cuts metal?](https://atoneplace.net/which/blade-metal/)
- [Which blade cuts tile?](https://atoneplace.net/which/blade-tile/)
- [Which circular saw blade for wood?](https://atoneplace.net/which/blade-wood/)
- [Which blade cuts plywood without tearout?](https://atoneplace.net/which/blade-plywood/)
- [Which blade cuts brick?](https://atoneplace.net/which/blade-brick/)
- [Which blade cuts laminate?](https://atoneplace.net/which/blade-laminate/)
- [Which blade cuts acrylic?](https://atoneplace.net/which/blade-acrylic/)
- [Which blade cuts glass?](https://atoneplace.net/which/blade-glass/)
- [Which blade cuts plasterboard?](https://atoneplace.net/which/blade-plasterboard/)

## Sources

- Typical range compiled from manufacturer specifications — At One Place (/about/)